Polymer–Inorganic Core–Shell Nanofibers by Electrospinning and Atomic Layer Deposition: Flexible Nylon–ZnO Core–Shell Nanofiber Mats and Their Photocatalytic Activity
Top Cited Papers
- 1 November 2012
- journal article
- research article
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 4 (11), 6185-6194
- https://doi.org/10.1021/am3017976
Abstract
Polymer-inorganic core-shell nanofibers were produced by two-step approach; electrospinning and atomic layer deposition (ALD). First, nylon 6,6 (polymeric core) nanofibers were obtained by electrospinning, and then zinc oxide (ZnO) (inorganic shell) with precise thickness control was deposited onto electrospun nylon 6,6 nanofibers using ALD technique. The bead-free and uniform nylon 6,6 nanofibers having different average fiber diameters (similar to 80, similar to 240 and similar to 650 nm) were achieved by using two different solvent systems and polymer concentrations. ZnO layer about 90 nm, having uniform thickness around the fiber structure, was successfully deposited onto the nylon 6,6 nanofibers. Because of the low deposition temperature utilized (200 degrees C), ALD process did not deform the polymeric fiber structure, and highly conformal ZnO layer with precise thickness and composition over a large scale were accomplished regardless of the differences in fiber diameters. ZnO shell layer was found to have a polycrystalline nature with hexagonal wurtzite structure. The core-shell nylon 6,6-ZnO nanofiber mats were flexible because of the polymeric core component. Photocatalytic activity of the core-shell nylon 6,6-ZnO nanofiber mats were tested by following the photocatalytic decomposition of rhodamine-B dye. The nylon 6,6-ZnO nanofiber mat, having thinner fiber diameter, has shown better photocatalytic efficiency due to higher surface area of this sample. These nylon 6,6-ZnO nanofiber mats have also shown structural stability and kept their photocatalytic activity for the second cycle test. Our findings suggest that core-shell nylon 6,6-ZnO nanofiber mat can be a very good candidate as a filter material for water purification and organic waste treatment because of their photocatalytic properties along with structural flexibility and stability.This publication has 64 references indexed in Scilit:
- Ethanol sensors based on ZnO nanotubes with controllable wall thickness via atomic layer deposition, an O2 plasma process and an annealing processSensors and Actuators B: Chemical, 2012
- Electrospinning of nanofibers from non-polymeric systems: polymer-free nanofibers from cyclodextrin derivativesNanoscale, 2012
- Multifunctional ZnO/Nylon 6 nanofiber mats by an electrospinning–electrospraying hybrid process for use in protective applicationsScience and Technology of Advanced Materials, 2011
- Effects of γ‐aminopropyltriethoxylsilane on morphological characteristics of hybrid nylon‐66‐based membranes before electron beam irradiationJournal of Applied Polymer Science, 2011
- A synthesis and sensing application of hollow ZnO nanofibers with uniform wall thicknesses grown using polymer templatesNanotechnology, 2010
- Photocatalytic Comparison of TiO2 Nanoparticles and Electrospun TiO2 Nanofibers: Effects of Mesoporosity and Interparticle Charge TransferThe Journal of Physical Chemistry C, 2010
- Synthesis and White-Light Emission of ZnO/HfO2: Eu NanocablesNanoscale Research Letters, 2010
- ZnO Hollow Nanofibers: Fabrication from Facile Single Capillary Electrospinning and Applications in Gas SensorsThe Journal of Physical Chemistry C, 2009
- Putting Electrospun Nanofibers to Work for Biomedical ResearchMacromolecular Rapid Communications, 2008
- Multiple melting and crystallization of nylon‐66/montmorillonite nanocompositesJournal of Polymer Science Part B: Polymer Physics, 2003