Melt- vs. Non-Melt Blending of Complexly Processable Ultra-High Molecular Weight Polyethylene/Cellulose Nanofiber Bionanocomposite
Open Access
- 27 January 2021
- Vol. 13 (3), 404
- https://doi.org/10.3390/polym13030404
Abstract
The major hurdle in melt-processing of ultra-high molecular weight polyethylene (UHMWPE) nanocomposite lies on the high melt viscosity of the UHMWPE, which may contribute to poor dispersion and distribution of the nanofiller. In this study, UHMWPE/cellulose nanofiber (UHMWPE/CNF) bionanocomposites were prepared by two different blending methods: (i) melt blending at 150 °C in a triple screw kneading extruder, and (ii) non-melt blending by ethanol mixing at room temperature. Results showed that melt-processing of UHMWPE without CNF (MB-UHMWPE/0) exhibited an increment in yield strength and Young’s modulus by 15% and 25%, respectively, compared to the Neat-UHMWPE. Tensile strength was however reduced by almost half. Ethanol mixed sample without CNF (EM-UHMWPE/0) on the other hand showed slight decrement in all mechanical properties tested. At 0.5% CNF inclusion, the mechanical properties of melt-blended bionanocomposites (MB-UHMWPE/0.5) were improved as compared to Neat-UHMWPE. It was also found that the yield strength, elongation at break, Young’s modulus, toughness and crystallinity of MB-UHMWPE/0.5 were higher by 28%, 61%, 47%, 45% and 11%, respectively, as compared to the ethanol mixing sample (EM-UHMWPE/0.5). Despite the reduction in tensile strength of MB-UHMWPE/0.5, the value i.e., 28.4 ± 1.0 MPa surpassed the minimum requirement of standard specification for fabricated UHMWPE in surgical implant application. Overall, melt-blending processing is more suitable for the preparation of UHMWPE/CNF bionanocomposites as exhibited by their characteristics presented herein. A better mechanical interlocking between UHMWPE and CNF at high temperature mixing with kneading was evident through FE-SEM observation, explains the higher mechanical properties of MB-UHMWPE/0.5 as compared to EM-UHMWPE/0.5.Funding Information
- Ministry of Higher Education Malaysia (6369111)
This publication has 69 references indexed in Scilit:
- Effect of gamma irradiation on the optical properties of UHMWPE (Ultra-high-molecular-weight-polyethylene) polymerNuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms, 2012
- Mechanical, Rheological, and Bioactivity Properties of Ultra High-Molecular-Weight Polyethylene Bioactive Composites Containing Polyethylene Glycol and HydroxyapatiteThe Scientific World Journal, 2012
- Drying cellulose nanofibrils: in search of a suitable methodCellulose, 2011
- High-porosity aerogels of high specific surface area prepared from nanofibrillated cellulose (NFC)Composites Science and Technology, 2011
- Mechanical properties of cellulose nanofiber (CNF) reinforced polylactic acid (PLA) prepared by twin screw extrusionComposites Science and Technology, 2010
- Strain hardening of high density polyethyleneJournal of Polymer Science Part B: Polymer Physics, 2007
- Advances in the processing, sterilization, and crosslinking of ultra-high molecular weight polyethylene for total joint arthroplastyBiomaterials, 1999
- Equilibrium triple point pressure and pressure-temperature phase diagram of polyethylenePolymer, 1992
- Kinetics of mechanical degradation in melts under model conditions and during processing of polymers—A reviewPolymer Degradation and Stability, 1987
- An Empirical Method for Estimating the Degree of Crystallinity of Native Cellulose Using the X-Ray DiffractometerTextile Research Journal, 1959