Synthesis and Characterization of Polyion Complex Membranes Made of Aminated Polyetherimide and Sulfonated Polyethersulfone for Fuel Cell Applications
- 1 December 2015
- journal article
- Published by ASME International in Journal of Fuel Cell Science and Technology
- Vol. 12 (6), 061004
- https://doi.org/10.1115/1.4031959
Abstract
Acid–base blends of sulfonated polyethersulfone (SPES) with pristine and aminated polyetherimide (APEI) are synthesized. Three blends polyethersulfone (PES)/polyetherimide (PEI), SPES/PEI, and SPES/APEI are prepared and characterized to evaluate their structural, morphological, mechanical, and other properties. Ion exchange capacity (IEC) of SPES/APEI and SPES/PEI blend membranes was determined to be 3.0 and 2.7 meq g−1, which is a substantial improvement over the 1.0 meq g−1 exhibited by unmodified PES/PEI blend. The proton conductivity of 0.093 S cm−1 displayed by SPES/APEI blend is found to be comparable to that of commercial Nafion membrane (0.056 S cm−1) and far superior to conductivities of 0.091 and 0.082 S cm−1 shown by SPES/PEI and PES/PEI blends, respectively. Further, water sorption observed in case of SPES/APEI and SPES/PEI blends was in the range 17–18% over a soaking time period of 12 hrs, which is ideal for proton conduction accompanied by low-membrane swelling. The methanol permeabilities of SPES/APEI and SPES/PEI blends are found to be 2.5 × 10−7 and 3.47 × 10−7 cm2 s−1, respectively. Compared to unmodified PES/PEI blend which revealed a methanol sorption of 12.3%, the modified blends SPES/PEI (9.6%) and SPES/APEI (7.5%) exhibited much lower methanol uptake over a sorption time of 12 hrs, indicating their capacity for low fuel bypass. The results demonstrate the promising potential of polymer blends made by combining a sulfonated polymer with an aminated polymer, such as SPES/APEI for fuel cell (FC) applications.Keywords
This publication has 36 references indexed in Scilit:
- Ion exchange membranes based upon crosslinked sulfonated polyethersulfone for electrochemical applicationsJournal of Membrane Science, 2014
- Polymer electrolyte membrane with high selectivity ratio for direct methanol fuel cells: A preliminary study based on blends of partially sulfonated polymers polyaniline and PVdF-co-HFPApplied Energy, 2014
- Preparation and properties of cross-linked sulfonated poly(imide-siloxane) for polymer electrolyte fuel cell applicationJournal of Power Sources, 2013
- Novel Blend Membranes Based on Acid-Base Interactions for Fuel CellsPolymers, 2012
- Sulfonated PEEK-based polymers in PEMFC and DMFC applications: A reviewInternational Journal of Hydrogen Energy, 2012
- Influence of crystal morphology of 1H-1,2,4-triazole on anhydrous state proton conductivity of sulfonated bisphenol A polyetherimide based polyelectrolytesPolymer, 2009
- Transport properties of polymer blend membranes of sulfonated and nonsulfonated polysulfones for direct methanol fuel cell applicationMacromolecular Research, 2008
- Applications of proton exchange membrane fuel cell systemsRenewable and Sustainable Energy Reviews, 2007
- A review of polymer electrolyte membranes for direct methanol fuel cellsJournal of Power Sources, 2007
- Blend membranes based on disulfonated poly(aryl ether ether ketone)s (SPEEK) and poly(amide imide) (PAI) for direct methanol fuel cell usagesPolymer, 2007