Investigation of Mechanical Behavior of Carbon Nanotube Reinforced Aluminum Matrix AlMg / KNT Composites
Open Access
- 17 May 2018
- journal article
- Published by Canakkale Onsekiz Mart University in Çanakkale Onsekiz Mart Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 4 (1), 99-109
- https://doi.org/10.28979/comufbed.359796
Abstract
En tr In this study, AlMg / KNT nanocomposite materials reinforced with KNT reinforced with different proportions (2.5%, 5% and 10%) to AlMg matrix were synthesized using powder metallurgy technique. The mechanical alloying (MA) process was carried out in Turbula mixing device for 7 hours and 400 rpm. After mechanical alloying, powder characterization, optical examinations, hardness and density tests were carried out. The XRD spectrometer was scanned at 10-90 degrees to sensitively XRD the specimen, and then samples of metal mold under 200 MPa pressure were produced. Composite samples of AlMg/KNT produced were sintered at different temperatures (350 ºC, 400 ºC, 450 ºC) for 120 minutes under high vacuum, and hardness, density and metallographic investigations of the samples were made. In the same atmosphere, an increase of 42,6º visibly was observed with increasing CNT ratios in peak intensities of AlMg / KNT composite specimens produced with different temperature and different CNT ratios. Along with the increased KNT ratio in the same way, the improvement of the hardness values due to the sintering temperature and the corresponding decrease in the density of KNT were observed. Bu çalışmada, toz metalürjisi tekniği kullanılarak AlMg matriksine ağırlıkça farklı oranlar da (%2,5, %5 ve %10) KNT takviyesi ile güçlendirilmiş AlMg/KNT nano kompozit materyalleri sentezlenmiştir. Mekanik alaşımlama (MA) işlemi 7 saat ve 400 Rpm de Turbula karıştırma cihazında yapılmıştır. Mekanik alaşımlamanın ardından sırası ile toz karekterizasyonu, optik incelemeler, sertlik ve yoğunluk testleri yapılmıştır. XRD spektrometre cihazında 10-90 derecede taranarak hassasiyetle XRD incelenmiş ardından 200 Mpa basınç altında metal kalıpta numuneler üretilmiştir. Üretilen AlMg/KNT kompozit numuneleri yüksek vakum altında farklı (350 0C, 400 0C, 450 0C) sıcaklıklar da 120 dakika boyunca sinterlenerek üretilen numunelerin sertlik, yoğunluk ve metalografik incelemeleri yapılmıştır. Aynı atmosferde, farklı sıcaklık ve farklı KNT oranlar ile üretilmiş olan AlMg/KNT kompozit numunelerin pik şiddetlerinde artan KNT oranları ile birlikte 42,6º gözle görülür şekilde artış gözlemlenmiştir. Aynı şekilde artan KNT oranı ile birlikte sinterleme sıcaklığına bağlı olarak sertlik değerlerinde iyileşme ve buna karşılık artan KNT oranı ile birlikte yoğunluk düşüşü gözlemlenmiştir.This publication has 21 references indexed in Scilit:
- Investigation of carbon nanotube reinforced aluminum matrix composite materialsComposites Science and Technology, 2010
- Realization of high strength and high ductility for AZ61 magnesium alloy by severe warm workingScience and Technology of Advanced Materials, 2005
- Enhanced ductility in strongly textured magnesium produced by equal channel angular processingScripta Materialia, 2004
- Texture development and its effect on mechanical properties of an AZ61 Mg alloy fabricated by equal channel angular pressingActa Materialia, 2003
- Effect of Microstructural Factors on Tensile Properties of an ECAE-Processed AZ31 Magnesium AlloyMATERIALS TRANSACTIONS, 2003
- Growth of a single freestanding multiwall carbon nanotube on each nanonickel dotApplied Physics Letters, 1999
- Plasma spray: Study of the coating generationCeramics International, 1996
- Exceptionally high Young's modulus observed for individual carbon nanotubesNature, 1996
- Nanomechanics of Carbon Tubes: Instabilities beyond Linear ResponsePhysical Review Letters, 1996
- Helical microtubules of graphitic carbonNature, 1991